[Aug-2023] The NACE NACE-CIP2-001 Exam Test For Brief Preparation [Q55-Q70]

Share

[Aug-2023] The NACE NACE-CIP2-001 Exam Test For Brief Preparation 

Revolutionary Guide To Exam NACE Dumps


NACE-CIP2-001 exam is an internationally recognized certification for coating inspectors who have a good understanding of coating materials, surface preparation, and application techniques. Coating Inspector Level 2 certification is designed to ensure that coating inspectors have the knowledge and skills needed to perform their job effectively. Coating Inspector Level 2 certification is recognized in the industry as a standard for coating inspectors, and it is highly sought after by companies that require coatings inspections. If you are a coating inspector looking to advance your career, then the NACE-CIP2-001 certification is definitely worth considering.

 

NEW QUESTION # 55
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be

  • A. run through the air wash separator.
  • B. mixed with uncontaminated abrasive
  • C. washed with clean potable water prior to Use.
  • D. disposed of properly.

Answer: D


NEW QUESTION # 56
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?

  • A. Distribution
  • B. Midstream
  • C. Transmission
  • D. Gathering

Answer: A


NEW QUESTION # 57
Surface preparation methods for Non-ferrous metals are:

  • A. The same as for Ferrous metals
  • B. Not required
  • C. Specific for each type of Non-ferrous metal
  • D. The same for all Non-FetT0us metals

Answer: C


NEW QUESTION # 58
Individuals conducting Coating Surveys should:

  • A. Always be trained and experienced Coating Industry
  • B. Always be NACE Level 3 Certified Inspectors
  • C. Always be NACE or SSPC Protective coating Specialists
  • D. Always be experienced Specification Writers

Answer: A


NEW QUESTION # 59
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.

  • A. False
  • B. True

Answer: B


NEW QUESTION # 60
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)

  • A. False
  • B. True

Answer: B


NEW QUESTION # 61
When performing testing in accordance with ASTM D 2583 the inspector may observe:

  • A. Glue failure
  • B. Cold flow or creep
  • C. Cohesion failure
  • D. Adhesion failure

Answer: B


NEW QUESTION # 62
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?

  • A. Liquid epoxies
  • B. Coal Tar Enamel
  • C. Concrete
  • D. Heat-shrink sleeves

Answer: A


NEW QUESTION # 63
Which is used to calibrate a pH meter?

  • A. Standard solvent solution
  • B. Deionized water
  • C. Distilled water
  • D. Standard buffer solution

Answer: D


NEW QUESTION # 64
Thermal Spray coatings provide:

  • A. Inhibitive protection
  • B. Sacrificial protection
  • C. Thermal protection
  • D. Barrier protection

Answer: B


NEW QUESTION # 65
NACE Standards include:

  • A. a) & b)
  • B. a) only
  • C. Standard Practices
  • D. Material Requirements

Answer: A


NEW QUESTION # 66
The most likely area of failure on a buried external pipeline coating is the:

  • A. Mainline coating
  • B. Ground bed
  • C. Areas exposed to Ultra Violet light
  • D. Field joint coating

Answer: D


NEW QUESTION # 67
Dehumidification is defined as the removal of moisture vapor from the air to

  • A. lower its temperature
  • B. provide worker comfort.
  • C. raise its relative humidity.
  • D. lower its dew point,

Answer: D


NEW QUESTION # 68
Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:

  • A. Conductive coatings applied to a magnetic metallic substrate
  • B. Non-Conductive coatings applied to a conductive metallic substrate
  • C. Conductive coatings applied to a cementitious substrate
  • D. Magnetic coatings applied to a magnetic metallic substrate

Answer: B


NEW QUESTION # 69
NACE No.13/ SSPC 6 identifies the use of:

  • A. Abrasive blasting only
  • B. Steam cleaning only
  • C. Various methods of cleaning
  • D. Watterjetting only

Answer: C


NEW QUESTION # 70
......

NACE-CIP2-001 Free Study Guide! with New Questions: https://dumpspdf.free4torrent.com/NACE-CIP2-001-valid-dumps-torrent.html